Yes, from my research the 2019 Toyota Highlander is equipped to handle the weight of Longneck XL Trailer and the Yakima HoldUp part # Y02443-2 using the Curt Multi-Purpose ball mount part # D210 as long as your hitch is rated for the weight of these items. The trailer weight rating in your owner's manual is 1500 lbs but you are only as strong as the weakest component of your setup which is most likely your trailer hitch in your case.
Please keep in mind the Curt Multi-Purpose Ball mount... view full answer...
I have an option for you but there is not a multi-purpose ball mount like part # D210 available that is designed with a rise.
I recommend to use the Malone 2" Dual Purpose Hitch Receiver part # MPG544 which is designed to carry an accessory and tow a trailer. You would just use a ball mount with a 2" rise in the adapter like part # C45155 which has a 2-1/4" rise and includes a pre-welded 2" ball. Please keep in mind the use of any hitch adapter cuts the tongue weight capacity of the... view full answer...
The Trailer Hub and Drum Assembly # AKHD-545-35-K does include a lithium complex grease like the LubriMatic Multi-Purpose Lithium Grease # L11315. This product specific grease is highly versatile and work well in the wheel bearings as well as other points on your trailer. While the LubriPlate Poly HP-2 Wheel Bearing Grease # L11465 is more heat resistant at 500 degrees Fahrenheit versus 350 degrees on the Lithium, your trailer hubs are unlikely to exceed that temperature. view full answer...
I'm not quite sure what the measurements would be for your F-450's fuel tank opening so I've attached a couple of drawings below of the Ultra-Fab Locking Multi-Purpose Access Door for RVs # UF48-979010 showing the dimensions of the access door and its mounting holes so you can verify with the dimensions of your fuel port. view full answer...
The TremPro 645 Silicone All Purpose Sealant for RVs and Trailers # FAS59FR would work great for you as it is a multi-purpose sealant that would work great with plastic. view full answer...
The Roadmaster Hi-Lo Hitch Adapter is not meant to be used with a ballmount like the Curt Multi Purpose Ball Mount.
The adapter is meant for rolling loads that do not exert any tongue weight, like a vehicle being flat towed by a Tow Bar.
The Curt Multi-Purpose Ball Mount could be used directly in your hitch receiver, without using the High-Lo Adapter, as long as the tongue weight of the tow dolly, the weight of the bike rack and the bikes attached to it do not exceed the 600 lb tongue... view full answer...
This product, LubriMatic # L11358, is a general purpose bio-based lithium grease and will behave differently than a typical petroleum-based grease. While it is fine for most applications that call for a petroleum-based grease, UltraLube Biobased White Lithium Grease is not suitable for packing wheel bearings.
Your needs will be better served with a product such as LubriMatic Marine Trailer Wheel Bearing Grease, # L54FR in 3-oz cartridges and a mini grease gun # 30-800, which is petroleum-based.... view full answer...
The B&W Silencer Pad for B&W 2-Inch Tow & Stow Multi-Ball Mounts # BWTS35020 is meant for use with their Tow & Stow Multi-Ball Mounts like # BWTS10037B. It is sized specifically for use with this series of ball mounts but there will certainly be other brands of hitch and ball mount that can use it.
For a good general-purpose anti-rattle device for use with a 2-inch hitch and ball mount I suggest the Roadmaster Quiet Hitch # RM-061. This will work on any 2-inch hitch receiver that has a... view full answer...
I spoke with a representative of Yakima, and they told me their bike rack could, in fact, be used with a multi-purpose ball mount such as the Curt # D210. view full answer...
The High-Low adapter # RM-076 was not designed to be used for that purpose. The adapter has a tongue weight capacity of only 100 lbs, and is designed for towing a vehicle that is resting on the ground behind another vehicle.
The Curt Multi-Purpose Ball Mount, # D210 might possibly be an option. The ball mount would raise your bike rack by 4-3/4 inches. The unit is rated at 7500 lbs towing, 750 lbs tongue weight. The receiver portion has a tongue weight capacity of 350 lbs. view full answer...
It can but the LMX Red Grease item # L11390 is the best overall grease for boat trailers. It is a waterproof marine grade grease that will not break down when exposed to water.
If you need a grease gun I recommend the LubriMatic Standard-Duty, Lever Action Grease Gun item # L30200. view full answer...
Yes, you will be able to load your 600lb garden tractor on the Detail K2 Mighty Multi A-Frame Utility Trailer # K2MMT5X7. The trailer will need to be tilted and for loading purposes Detail K2 recommends no more than 400lbs on the tailgate itself. As your tractor will not have that amount on the tailgate all at one time you will not have issues when loading.
We do have some Valterra Non-Skid Grip Tape # A10-2260 that will help the tractor get up the slope of the trailer in wet conditions. view full answer...
You could use white lithium grease or we recommend using the LubriMatic Multi-Purpose Lithium Grease # L11316 for your Curt A20 5th Wheel Trailer Hitch # C16140. The Curt maintenance guide just says to use high-pressure wheel bearing grease as being the preferred option. view full answer...
I can confirm that, according to Thule, the # TH830 Stacker Rooftop Multi-Kayak Carrier fits factory crossbars on a 2011 Honda CR-V. Assuming your aftermarket bars are the same as the factory crossbars, this will be able to mount on your vehicle.
This carrier requires 24" minimum bar spread for proper mounting and holds up to 4 kayaks. It folds down flat for a cleaner look when not in use. The kayak you are carrying can be no longer than 10 feet for this carrier.
I have attached a video... view full answer...
There is not a way to attach a sway bar tab to that ball mount, or a way to use a bike rack and weight distribution with an adapter. If your 2023 Kia Telluride has a roof rack you can use a roof-mounted rack like the Yakima FrontLoader # Y02103. Alternatively you can use a trunk-mounted rack if you like, the Yakima FullBack # Y02634. view full answer...
After speaking with my contact at CE Smith, I found the CE Smith Pyramid Washer # CE10806 fits against the nut high side up. To demonstrate how this would work, I have included a video that should be helpful.
This washer works best with the CE Smith U-Bolt # CE15252A, a multi-purpose U-bolt intended for use on trailer to help secure brackets, mounts, and cargo. It is constructed of sturdy, zinc-plated steel, and it comes with mounting hardware. view full answer...
Absolutely, to install trailer wiring on your 2024 GMC Canyon you will need the Hopkins Multi-Tow 7-Way Blade and 4-Way Flat Trailer Connector # HM11141144. This uses a factory style connector so you will be able to place the connector easily in place of the factory cover on your bumper. Then you will simply wire in the included pigtail to the wires located behind your rear bumper.
The Curt Trailer Hitch Receiver # C78VV you found is confirmed to fit your Canyon.
If you are needing a... view full answer...
The LubriMatic Mini Grease Gun Kit with Multi-Purpose Grease # L30132 is a compact and cost-effective tool-box-size grease gun. It will work with E-Z Lube grease zerk fittings such as those found on trailer spindles and on Bearing Buddy grease caps like # BB1980A-SS.
If you are looking for a grease gun and grease specifically for lubricating your enclosed trailer's tandem axle bearings this general-purpose grease will be fine. If you want to use a heavier-duty unit we offer Performance... view full answer...
The grease for the Dexter Trailer Idler Hub Assembly for 2,000-lb Axles # 34822545BX is a lithium grease like the Dexter Multi-Purpose Lithium Grease # DX64TR.
The hub comes pre-greased so you do not need at add any more when installing. Then in regards to Bearing Buddies the correct fit for this hub is the Bearing Buddy Bearing Protectors # BB1980A. view full answer...
The Curt Multipurpose Ball Mount with 2-Inch Receiver # D210 will fit the hitch on your 2002 Infiniti QX4 as long as that hitch is a 2-inch Class 3 type like the Curt # 13088 or one of the others shown on the linked page. I linked an article to help you identify your hitch type.
Installed in such a compatible hitch this multi-purpose ball mount provides a 2-inch receiver opening for using a 2-inch hitch-mount accessory.
Keep in mind that the hitch (and the vehicle itself) must be rated... view full answer...
Go To Results